The Malmet DC series of Drying Cabinets are designed to dry respiratory tubing, face masks, surgical instruments
Dual over temperature cut-out. Set point temperatures are locked to prevent unauthorised change.
Cabinet temperature is pre-set at 70°C and governed not to exceed this temperature.
A modular hanging system with shelving and trays to suit any requirement.
A centrifugal fan drives heated air downwards to provide rapid internal drying of suspended corrugated tubing and circulate warmth throughout the chamber.
A quality cabinet built for years of continuous use. The Malmet factory is ISO9002 certified and all Malmet products are backed by a one year warranty
A cabinet which can handle large loads with any combination of tubes and parts.
Connects to standard hospital power outlets; a vent connection removes heated air.
Centre opening doors protrude only 330mm when fully open. Pass through wall units are available.
Double wall stainless steel construction with an insulated cavity, combined with double glazed doors. Heating is discontinued when doors are open.
A washable filter removes fluff, lint, dust etc.
Meets both AS2514 (Drying Cabinets for Medical Equipment) and As2774 (Drying Cabinets for Respiratory Equipment)
DC11 setup of
Anaesthetic Drying Cabinet
Click here to enquire about the Malmet Anaesthetic Drying Cabinets.
Product Specifications —
Product Codes — Spare Parts
|Outside Dimensions (mm)
||1750h x 750w x 640d
|Outside Dimensions Pass Through
||1750h x 600w x 690d
|Chamber Dimensions (mm)
||1152h x 600w x 560d
||Double Glazed Tempered, Centre Opening with Magnetic Door Closure
||Damper controlled to air-conditioner return duct or direct to atmosphere
|Air Filter (mm)
||150 x 150 x 15 washable polyurethane
|Air Bleed Off
||Automatic Damper Control
|Electrical (Australia Only)
||Plug into 15amp GPO
||Electro polished stainless steel wire
|Front Loading Drying Cabinet
||FRONT LOAD Mixed 6 half width wire shelves, 2 Racks of 18 x 37mm Dia Tube holders.
||FRONT LOAD Mixed 6 half width Wire Shelves 2 Racks of 18 x 37mm Dia Tube holders with Timer.
||FRONT LOAD 6 Full Width Wire Shelves - No Tube holders.
||FRONT LOAD 6 Full Width Wire Shelves - No Tube holders with Timer.
||FRONT LOAD Full Hanging, 5 Rack of 18 x 37mm Dia Tube Holders.
||FRONT LOAD Full Hanging, 5 Rack of 18 x 37mm Dia Tube Holders with Timer.
|Pass Through Drying Cabinet
||FRONT LOAD & REAR UN-LOAD (PASS THROUGH), Mixed 6 half width wire Shelves 2 racks of 18 x 37mm Dia Tube Holders.
||FRONT LOAD & REAR UN-LOAD (PASS THROUGH), Mixed 6 half width wire Shelves 2 racks of 18 x 37mm Dia Tube Holders with Timer.
||FRONT LOAD & REAR UN-LOAD (PASS THROUGH), 6 Full Width wire Shelves-No tube Holders.
||FRONT LOAD & REAR UN-LOAD (PASS THROUGH), 6 Full Width wire Shelves-No tube Holders with Timer.
||FRONT LOAD & REAR UN-LOAD (PASS THROUGH), Full Hanging 5 Racks of 18 x 37mm Dia Tube Holders.
||FRONT LOAD & REAR UN-LOAD (PASS THROUGH), Full Hanging 5 Racks of 18 x 37mm Dia Tube Holders with Timer.
|Accessories ⁄ Spare Parts
||Instrument Tray, 362 x 271 x 22mm
||Air Diffuser Blank
||Air Diffuser (with holes)
||Anaesthetic Bag Holder, Double Sided 6
||Part width shelf DC11 ⁄ DC21 models. Size 520d x 340w
||Part width shelf DC12 ⁄ DC22 models. Size 520d x 600w
||10 x 50mm Diameter tube holder
||16 x 37mm Diameter tube holder (models prior to Feb 2002)
||18 x 37mm Diameter tube holder
||Door Lock Bolt Assembly (must be factory fitted)
Return to top of page